This European Standard was approved by CENELEC on 2009-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This European Standard applies to a security fog system that is part of an Intruder and Hold-up Alarm.
This document is applicable to rocking equipment which is used as playground equipment for children, as defined in the document. Where the main play function is not rocking, the relevant requirements in this document may be used, as appropriate.This document specifies additional safety requirements and test methods for seesaws and rocking equipment intended for permanent...
This European Standard specifies additional safety requirements for slides intended for permanent installation for use by children. The aim is to provide protection to the user against possible hazards during use. Where the main play function is not sliding, the relevant requirements in this part of EN 1176 may be used, as appropriate. This document is not applicable to...
This standard is Part 1 in a series on the safety of playground equipment and surfacing. The series was developed to provide EU harmonized safety benchmarks for children’s playground equipment. The objective is to allow children of differing abilities and ages as many exciting play opportunities as possible, with as much safety as necessary.
This European Standard specifies additional safety requirements for swings intended for permanent installation for use by children. Where the main play function is not swinging, the relevant requirements in this part of EN 1176 may be used, as appropriate. NOTE Recommendations on the design and siting of swings are given in Annex A.
IEC TS 61850-80-4:2016(E) defines the one-to-one relationship of IEC 62056 OBIS codes to IEC 61850 Logical Nodes. The purpose is to increase the availability of revenue meter information to other applications defined within the IEC 61850 framework. This increased visibility will contribute to information available for smart grid applications
IEC/TR 61850-1:2013 is applicable to power utility automation systems and defines the communication between intelligent electronic devices in such a system, and the related system requirements. This part gives an introduction and overview of the IEC 61850 standard series. This edition includes the following significant technical changes with respect to the previous edition: -...
This part of IEC 61850 specifies a precision time protocol (PTP) profile of IEC 61588:2009 ¦ IEEE Std 1588-2008 applicable to power utility automation, which allows compliance with the highest synchronization classes of IEC 61850-5 and IEC 61869-9
This part of IEC 61850 defines the general requirements, mainly regarding construction, design and environmental conditions for utility communication and automation IEDs and systems in power plant and substation environments.
Applies to all lighting equipment, independent auxiliaries, UV and IR radiation equipment, neon advertising signs, street/flood lighting and transport lighting.
Specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. The requirements and related tests of this standard cover: classification, marking, mechanical construction, electrical construction and photobiological safety. This eighth edition cancels and replaces the seventh edition published in 2008. This...
The standard ΕΝ 15733:2009 is a new European Standard that specifies the requirements for the provision of real estate services , including consulting, marketing, contact between seller and buyer, rent, lease, leasing, evaluation and inspection.
EC 60598-2-5:2015 specifies requirements for floodlights for use with electrical light sources on supply voltages not exceeding 1 000 V. This third edition cancels and replaces the second edition published in 1998, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: it introduces...
ECSS Secretariat, Requirements & Standards Division, Noordwijk, The Netherlands, 31 July 2008. This Standard specifies the physical interconnection media and data communication protocols to enable the reliable sending of data at highspeed (between 2 Mb/s and 400 Mb/s) from one unit to another. SpaceWire links are fullduplex, pointtopoint, serial data communication links.
PDF BS EN 54-13:2017 Fire detection and fire alarm systems - Part 13: Compatibility and connectability assessment of system components. — 36 p. This document (EN 54-13:2017) has been prepared by Technical Committee CEN/TC 72 “Fire detection and fire alarm system”, the secretariat of which is held by BSI. This document supersedes EN 54-13:2005. This European Standard shall be...
This European Standard has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretatiat of which is held by DIN. This European Standard was approved by CEN on 1996-06-20. — 10 p. This standard specifies test methods and minimum performance requirements for reflective protective clothing used in...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 14 February 2005 and includes Amendment 1 approved by CEN on 5 April 2009. This document supersedes EN 13034:2005. — 13 p. This document specifies the...
This European Standard has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretatiat of which is held by DIN. This European Standard was approved by CEN on 22 July 2005. This European Standard supersedes EN 1146:1997. — 31 p. This European Standard specifies minimum requirements for self-contained open-circuit compressed air breathing...
This document EN 420:2003 has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm proteciton and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This document supersedes EN 420:1994. — 32 p. This standard defines the general requirements and relevant test procedures for...
This document has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretariat of which is held by DIN. This European Standard was approved by CEN 8 November 2001. This European Standard supersedes EN 405:1992. — 42 p. This European Standard specifies the performance requirements, test methods and marking requirements for valved filtering...
This document has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretariat of which is held by DIN. This European Standard was approved by CEN on 3 March 2005. This document supersedes EN 404:1993. — 43 p. This document refers to filtering devices designed for protection against carbon monoxide (filter self-rescuer). It specifies minimum...
This document has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretariat of which is held by DIN. This European Standard was approved by CEN on 17 January 2003. This document supersedes EN 402:1993. — 30 p. This European Standard specifies minimum requirements for lung governed demand self-contained open-circuit compressed air breathing...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This document supersedes EN 374-3:1994. — 14 p. This European Standard specifies the determination of the resistance of protective glove...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This documents supersedes EN 374-2:1994. — 11 p. This European Standard specifies a test method for the penetration resistance of gloves...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This document supersedes EN 374-1:1994. — 9 p. This standard specifies the requirements for gloves to protect the user agaings chemicals...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 16 April 2004. This document supersedes ENV 342:1998. — 21 p. This European Standard specifies requirements and test methods for performance of clothing...
This document has been prepared by CEN/NC 162, "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 3 November 2003. This European Standard supersedes EN 340:1993. — 25 p. This European Standard specifies general performance requirements for ergonomics, innocuousness, size...
This European Standard was approved by CEN on 25 December 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to...
Publication details not specified Purpose The purpose of this document is to harmonise evaluation of uncertainty of measurement within EA, to set up, in addition to the general requirements of EA, the specific demands in reporting uncertainty of measurement on calibration certificates issued by accredited laboratories and to assist accreditation bodies with a coherent...
This European Standard specifies requirements for classification in order to designate tubular cored electrodes with or without a gas shield for metal arc welding of steels, such as stainless and heat-resisting steels in terms of the chemical composition of the all-weld metal. It is recognized that the operating characteristics of tubular cored electrodes can be modified by the...
European standard for cryogenic equipment (english version). May 2000. — 14 p This standard specifies the minimum requirements for the design, manufacture and testing of pumps for cryogenic service (i.e. for cryogenic fluids, see EN 1251-1) This standard covers centrifugal pumps. However the principles may be applied to other types of pumps (e.g. reciprocating) This standard...
This document (EN 14587-3:2012) has been prepared by Technical Committee CEN/TC 256 Railway applications, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2013, and conflicting national standards shall be withdrawn at the latest...
285 p., 2000, Oxford: Butterworth-Heinemann, ISBN: 0-7506-4813-9 The prime aim of CE Conformity Marking and new approach directives is to enable readers to understand the requirements of the CE Directive and to see how it affects the European Directives. This book also provides guidance on the sort of Quality Management System that a manufacturer and/or supplier will need in...
This European Standard was approved by CEN on 29 May 2008. July 2008. Supersedes EN 115:1995. 91 p. This standard is applicable for new escalators and moving walks (pallet or belt type) as defined in Clause 3. This standard deals with all significant hazards, hazardous situations and events relevant to escalators and moving walks when they are used as intended and under...
Polski Komitet Normalizacyjny. Kwiecień 1999. 14 stron. Tolerancje wymiarów liniowych i kątowych bez indywidualnych oznaczeń tolerancji. Ustalono cztery klasy tolerancj i ogólnych wymiarów przedmiotów wykonanych metodą skrawania metali lub tłoczenia z blachy. Podano trzy tablice i załącznik informacyjny dotyczący koncepcji tolerowania ogólnego wymiarów.
PD CEN ISO/TR 3834-6:2007 gives guidelines for the implementation of requirements given in the other parts of BS EN ISO 3834, and is intended to help manufacturers and users select the part of BS EN ISO 3834 appropriate to their needs. It is expected that they will already be familiar with BS EN ISO 3834 series as a whole. Welding is a special process in that the final result...
EN 13444-1-2001 Road vehicles with electric traction. Measuring emissions from hybrid vehicles. Part 1. Thermal hybrid electric vehicles The document aims at defining the emission measurements for a thermal electric hybrid road vehicle from M1, N1, or M2 category, and for tricycles and quadricycles from the motorcycle types. The project applies to the above mentioned vehicles...
EN 13447-2001 Road vehicles with electric traction. Terminology The document gives definitions used in European standards for electrically propelled road vehicles. It is not intended to give definitions of all terms concerning these vehicles, but to permit a good understanding of the content of standards dealing with electrically propelled road vehicles.
EN 1986-2-2001 Electric vehicles. Energy performance measurement. Part 2. Hybrid thermoelectric cars The document aims at defining the range in pure electric driving mode and the consumption measurements for a thermal electric hybrid road vehicle from M1, N1, or M2 category, and for tricycles and quadricycles of the motorcycle types. This standard applies to the above mentioned...
EN 1986-1-1997 Electric vehicles. Energy performance measurement. Part 1. Electric cars This standard specifies the procedure to apply to measure the range and the consumption of the electrically propelled road vehicles (purely electric road vehicles). The document applies to vehicle categories M1, M2, N1 and N2, and to three and four wheel power driven vehicles from the motor...
EN 1821-1-1996 Electric road vehicles. Measuring road handling properties. Part 1. Clean electric cars. The document specifies test methods for measuring the road operating abilities of electrically propelled road vehicles (pure electric vehicles), and specifies road operating abilities which include vehicle speed, acceleration, hill climbing ability. It is applicable to...
This document is a comprehensive design code for concrete. It is the result of a comprehensive revision to the original model code of 1978, which was produced jointly by the Comité Euro-International du Béton (CEB) and the Fédération International de la Précontrainte (FIP). The original CEB-FIP Model Code of 1978 has had a considerable impact on the national design codes in...
This Technical Specification (CEN/TS) was approved by CEN on 11 July 2004 for provisional application. This Draft for Development is the official English language version of CEN/TS 14751:2004. 38 p. This document specifies the application of the time-of-flight diffraction (TOFD) technique for the semi-, or fullyautomated ultrasonic testing of fusion welded joints in metallic...
This European Standard was approved by CEN on 23 August 2007. The European Standard EN 1337-8:2007 has the status of a Polish Standard. 28 p. This Part of this European Standard deals with the requirements for the design and manufacture of Guide Bearings and Restraint Bearings. Guide Bearings and Restraint Bearings are not intended to transmit vertical loads but they may be...
This draft European Standard is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC 166. October 2002. 61 p. This part of prEN 13384 specifies methods for calculation of the thermal and fluid dynamic characteristics of chimneys serving more than one heating appliance. This part of prEN 13384 covers both the cases, either - 1 where...
This draft European Standard is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee ECISS/TC 19. January 2005. Will supersede ENV 10080:1995. 69 p. This document specifies general requirements and definitions for the performance characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as...
Scope Basic requirements General Human resources Human resources management Professional competences of translators Professional competences of revisers Professional competences of reviewers Continuing professional development Technical resources Quality management system Project management Client-TSP relationship General Enquiry and feasibility Quotation Client-TSP agreement...
This European Standard was approved by CEN on 30 April 2004. 25 p. This document specifies safety requirements relating to the materials, construction, performance, packaging and labelling of cutlery and feeding utensils. All products which are intended to be used by a child aged up to 36 months to eat by itself or with the assistance of another person are included in the scope...
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 322. May 2009. 62 p. This European Standard defines the general safety requirements for hot rolling mills for long products as defined in 3.1. This European Standard deals with significant hazards, hazardous situations and events relevant to hot rolling...
This European Standard was approved by CEN on 14 October 2004. 37 p. This Part of EN 10217 specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic-ferritic stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155. Will supersede EN 1555-1:2002. 16 p. This part of EN 1555 specifies the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels. It also specifies the test parameters for the test methods referred to in this...
This draft European standard is submitted to CEN members for formal vote. 2000. 29 p. This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in the construction of roads and other trafficked areas (excluding railways and asphaltic inclusion), and the appropriate test methods to determine these characteristics. This...
This European Standard was approved by CEN on 16 May 2007. 87 p. This European Standard specifies: – a structured list of control, building automation and technical building management functions which havean impact on the energy performance of buildings; – a method to define minimum requirements regarding the control, building automation and technical building management...
The European Parljament and the Council of the Euiropean Union, (OJ L 181, 9.7.1997, p. 1) . 29 May 1997. 68 p. This Directive applies to the design, manufacture and conformity assessment of pressure equipment and assemblies with a maximum allowable pressure PS greater than 0,5 bar.
Comments