This European Standard was approved by CENELEC on 2009-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This European Standard applies to a security fog system that is part of an Intruder and Hold-up Alarm.
This document is applicable to rocking equipment which is used as playground equipment for children, as defined in the document. Where the main play function is not rocking, the relevant requirements in this document may be used, as appropriate.This document specifies additional safety requirements and test methods for seesaws and rocking equipment intended for permanent...
This European Standard specifies additional safety requirements for slides intended for permanent installation for use by children. The aim is to provide protection to the user against possible hazards during use. Where the main play function is not sliding, the relevant requirements in this part of EN 1176 may be used, as appropriate. This document is not applicable to...
This standard is Part 1 in a series on the safety of playground equipment and surfacing. The series was developed to provide EU harmonized safety benchmarks for children’s playground equipment. The objective is to allow children of differing abilities and ages as many exciting play opportunities as possible, with as much safety as necessary.
This European Standard specifies additional safety requirements for swings intended for permanent installation for use by children. Where the main play function is not swinging, the relevant requirements in this part of EN 1176 may be used, as appropriate. NOTE Recommendations on the design and siting of swings are given in Annex A.
IEC TS 61850-80-4:2016(E) defines the one-to-one relationship of IEC 62056 OBIS codes to IEC 61850 Logical Nodes. The purpose is to increase the availability of revenue meter information to other applications defined within the IEC 61850 framework. This increased visibility will contribute to information available for smart grid applications
IEC/TR 61850-1:2013 is applicable to power utility automation systems and defines the communication between intelligent electronic devices in such a system, and the related system requirements. This part gives an introduction and overview of the IEC 61850 standard series. This edition includes the following significant technical changes with respect to the previous edition: -...
This part of IEC 61850 specifies a precision time protocol (PTP) profile of IEC 61588:2009 ¦ IEEE Std 1588-2008 applicable to power utility automation, which allows compliance with the highest synchronization classes of IEC 61850-5 and IEC 61869-9
This part of IEC 61850 defines the general requirements, mainly regarding construction, design and environmental conditions for utility communication and automation IEDs and systems in power plant and substation environments.
Applies to all lighting equipment, independent auxiliaries, UV and IR radiation equipment, neon advertising signs, street/flood lighting and transport lighting.
Specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. The requirements and related tests of this standard cover: classification, marking, mechanical construction, electrical construction and photobiological safety. This eighth edition cancels and replaces the seventh edition published in 2008. This...
The standard ΕΝ 15733:2009 is a new European Standard that specifies the requirements for the provision of real estate services , including consulting, marketing, contact between seller and buyer, rent, lease, leasing, evaluation and inspection.
EC 60598-2-5:2015 specifies requirements for floodlights for use with electrical light sources on supply voltages not exceeding 1 000 V. This third edition cancels and replaces the second edition published in 1998, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: it introduces...
ISO 17491-4:2008 specifies methods for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity: Method A: low-level spray test. This is applicable to clothing that covers the full body surface and which is intended to be worn when there is a potential risk of exposure to small quantities of...
ISO 17491-3:2008 specifies a test method for determining the resistance of protective clothing against penetration by a jet of liquid. ISO 17491-3:2008 is applicable to clothing with liquid-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment worn with it. ISO 17491-3:2008 does not...
ISO/IEC 18033-5:2015 specifies identity-based encryption mechanisms. For each mechanism the functional interface, the precise operation of the mechanism, and the ciphertext format are specified. However, conforming systems may use alternative formats for storing and transmitting ciphertexts.
BS ISO 17493:2016 describes a test method for evaluating the heat resistance of protective clothing materials or items and equipment when exposed in a hot air circulating oven. The method is intended to evaluate physical changes in a material at a given exposure temperature. Materials are evaluated for defined visible changes including the measurement of shrinkage. Different...
ISO 22301 Societal security – Business continuity management systems – Requirements is a management system standard that specifies requirements to plan, establish, implement, operate, monitor, review, maintain and continually improve a documented management system to protect against, reduce the likelihood of occurrence, prepare for, respond to, and recover from disruptive...
ECSS Secretariat, Requirements & Standards Division, Noordwijk, The Netherlands, 31 July 2008. This Standard specifies the physical interconnection media and data communication protocols to enable the reliable sending of data at highspeed (between 2 Mb/s and 400 Mb/s) from one unit to another. SpaceWire links are fullduplex, pointtopoint, serial data communication links.
PDF BS EN 54-13:2017 Fire detection and fire alarm systems - Part 13: Compatibility and connectability assessment of system components. — 36 p. This document (EN 54-13:2017) has been prepared by Technical Committee CEN/TC 72 “Fire detection and fire alarm system”, the secretariat of which is held by BSI. This document supersedes EN 54-13:2005. This European Standard shall be...
This European Standard has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretatiat of which is held by DIN. This European Standard was approved by CEN on 1996-06-20. — 10 p. This standard specifies test methods and minimum performance requirements for reflective protective clothing used in...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 14 February 2005 and includes Amendment 1 approved by CEN on 5 April 2009. This document supersedes EN 13034:2005. — 13 p. This document specifies the...
This European Standard has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretatiat of which is held by DIN. This European Standard was approved by CEN on 22 July 2005. This European Standard supersedes EN 1146:1997. — 31 p. This European Standard specifies minimum requirements for self-contained open-circuit compressed air breathing...
This document EN 420:2003 has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm proteciton and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This document supersedes EN 420:1994. — 32 p. This standard defines the general requirements and relevant test procedures for...
This document has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretariat of which is held by DIN. This European Standard was approved by CEN 8 November 2001. This European Standard supersedes EN 405:1992. — 42 p. This European Standard specifies the performance requirements, test methods and marking requirements for valved filtering...
This document has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretariat of which is held by DIN. This European Standard was approved by CEN on 3 March 2005. This document supersedes EN 404:1993. — 43 p. This document refers to filtering devices designed for protection against carbon monoxide (filter self-rescuer). It specifies minimum...
This document has been prepared by Technical Committee CEN/TC 79 "Respiratory protective devices", the secretariat of which is held by DIN. This European Standard was approved by CEN on 17 January 2003. This document supersedes EN 402:1993. — 30 p. This European Standard specifies minimum requirements for lung governed demand self-contained open-circuit compressed air breathing...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This document supersedes EN 374-3:1994. — 14 p. This European Standard specifies the determination of the resistance of protective glove...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This documents supersedes EN 374-2:1994. — 11 p. This European Standard specifies a test method for the penetration resistance of gloves...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 24 July 2003. This document supersedes EN 374-1:1994. — 9 p. This standard specifies the requirements for gloves to protect the user agaings chemicals...
This document has been prepared by Technical Committee CEN/TC 162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 16 April 2004. This document supersedes ENV 342:1998. — 21 p. This European Standard specifies requirements and test methods for performance of clothing...
This document has been prepared by CEN/NC 162, "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN. This European Standard was approved by CEN on 3 November 2003. This European Standard supersedes EN 340:1993. — 25 p. This European Standard specifies general performance requirements for ergonomics, innocuousness, size...
This document has been prepared by Technical Committee CEN/TC162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 94 "Personal safety - Protective clothing and equipment". This European Standard was approved by CEN on 24 December 2004. This document supersedes EN...
This European Standard was approved by CEN on 25 December 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to...
Publication details not specified Purpose The purpose of this document is to harmonise evaluation of uncertainty of measurement within EA, to set up, in addition to the general requirements of EA, the specific demands in reporting uncertainty of measurement on calibration certificates issued by accredited laboratories and to assist accreditation bodies with a coherent...
This International Standard specifies the data fields used in the title blocks and headers of technical product documents. Its purpose is to facilitate the exchange of documents and ensure compatibility by defining field names, their contents and their length (number of characters). It covers manual as well as computer-based design work, and is applicable to all kinds of...
This European Standard specifies requirements for classification in order to designate tubular cored electrodes with or without a gas shield for metal arc welding of steels, such as stainless and heat-resisting steels in terms of the chemical composition of the all-weld metal. It is recognized that the operating characteristics of tubular cored electrodes can be modified by the...
This part of ISO 15614 specifies how a preliminary welding procedure specification is qualified by welding procedure tests. It applies to the arc and gas welding of copper and copper alloys in all product forms. This part of ISO 15614 defines the conditions for the execution of welding procedure tests and the range of qualification for welding procedures for all practical...
This European Standard is a part of a series of standards, details of this series are given in EN ISO 15607:2003, annex A. This standard specifies how a preliminary welding procedure specification is qualified based on pre-production welding tests. This standard is applicable to arc welding, gas welding, beam welding, resistance welding, stud welding and friction welding of...
This European Standard specifies general tolerances for linear and angular dimensions and for shape and position of welded structures in four tolerance classes, these being based on customary workshop accuracy. The main criterion for the selection of a particular tolerance class should be the functional requirements which are to be met.
European standard for cryogenic equipment (english version). May 2000. — 14 p This standard specifies the minimum requirements for the design, manufacture and testing of pumps for cryogenic service (i.e. for cryogenic fluids, see EN 1251-1) This standard covers centrifugal pumps. However the principles may be applied to other types of pumps (e.g. reciprocating) This standard...
This document (EN 14587-3:2012) has been prepared by Technical Committee CEN/TC 256 Railway applications, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2013, and conflicting national standards shall be withdrawn at the latest...